By pursuing your browsing on this website, you must accept the use and writing of Cookies on your device. These cookies (small text files) allow to follow your browsing, update your shopping cart, recognize you during your next visit and secure your connection. To set up the cookies, go to your browser's settings.
close
Rechargeable electronic referee beeper flags
  • Arm strap pager
  • Flag
  • Transport bag
  • Rechargeable electronic referee beeper flags

Rechargeable electronic referee beeper flags

€449.00

Including €0.20 for ecotax

Quantity
Item shipped in October
  • Free shipping (subject to conditions)
  • Payment in 3 free-of-charge installments (subject to conditions)
  • 2-year warranty

SignalBip rechargeable electronic beeper flags are designed to facilitate communication between referees during matches. The assistant referees may signal a foul to the main referee by simply pressing the handle of the flag, which will send a specific acoustic signal depending on the side where the assistant referee is located.

Set Content:

  • 2 screwable electronic beeper flags with radio transmitter for assistant referees
  • 1 arm strap pager with vibrating and sound signal for central referee
  • 3 rechargeable batteries 
  • 1 power supply unit and 1 5-line USB adapter cable
  • 1 transport bag
  • 1 multilingual manual

SignalBip rechargeable electronic beeper flags is the ideal equipment for referees. They are designed to help them effectively report key exits and offside.

Rechargeable flags: No need to replace batteries! 

This new generation of SignalBip electronic flags has been designed taking into account the remarks made by the arbitral body in order to best meet the needs of the referees:

Integration of a rechargeable battery in the 2 electronic flags and the arm strap pager

Improvement of the handles :

  • larger and wider for a better fit
  • more ergonomic
  • covered with a new less slippery material and adhesive pimple for a better grip
  • 1 LED battery status indicator: low or charged

Optimized average charging time (1h)

  • Energy saving function: use of the battery only when a button is pressed
  • Beeps with vibration are emitted when receiving a flag signal (4 sound levels: silent to loud).
  • Communication of the arm strap pager with up to 5 flags
  • All three products can be charged at the same time using the supplied power supply unit and its 5-line USB adaptor.
  • 1 Status LED indicator (ON/OFF) and 1 sound and battery LED indicator on the arm strap pager.
  • Low-battery detection: the « beep » sound speeds up and flashing is slower.
  • Energy-saving feature: use of the flag battery only when pressing its button.
  • The arm strap pager emits beeps and vibrates when receiving a signal from a flag ; adjust or turn off the volume 
  • Communication of the arm strap pager with beeper 5 flags maximum.
  • 100% polyester 40x40cm bright yellow and orange checkered flag cloth 
  • Guarantee: 2 years (excluding batteries)

Set Content:

  • 2 screwable electronic beeper flags with radio transmitter for assistant referees
  • 1 armband case with vibrating and sound signal for main referee
  • 3 rechargeable batteries
  • 1 power supply unit and 1 5-line USB adaptor
  • 1 modular transport case
  • 1 multilingual manual

Non-contractual photos

SBFK8
2019-11-07

Data sheet

Arm strap pager
104 x 60 x 26 mm
Flag with pole
635 x 46 x 44 mm
Transport bag
370 x 540 x 330 mm
Charging time
1 hour
Battery duration
20 hours
Frequency
863 to 870 MHz

Specific References

Download

User guide

Download (4.7M)

Data sheet

Download (696.5k)
    How should I charge the flags and the armband case?

    The electronic flags and the armband case can be recharged simultaneously with the supplied power supply unit and the USB adaptor. Make sure to observe the correct voltage indicated on the supplied power supply unit.


    How much time do I need to recharge the flag kit?

    For a complete recharge, the armband case and the flags must be recharged for approximately 1 hour for a theoretical battery life of 20 hours.


    How to learn the flags into the armband case?
    Go into Registration mode

    Arm strap pager

    1 - If it is switched off, switch it on by pressing the ON/OFF button.

    2 - Keep the ON/OFF and VOLUME buttons pressed for 3 seconds until the green BATTERY turns onThe LED will flash green while it is registering.

    Flag

    1 - If it is switched off, switch it on by pressing the SIGNAL button.

    2 - Keep the SIGNAL button pressed for 10 seconds, until the green LED turns onThe LED will flash green while it is registering.

    3 - Once registered, the flag will vibrate twice and the green LED will remain lit for 3 seconds before switching off. If the red LED flashes, the flag is not registered. You must perform the operation again.

    NOTE: A maximum of 5 flags may be registered in the arm strap pager.

    Quit Registration mode

    Arm strap pager: press once the ON/OFF or VOLUME button

    Flag: press once the SIGNAL button

    NOTE: The Registration automatically stops after 3 minutes.

    Faults

    If the flag vibrates twice and the green LED stays on for 3 seconds, it means that the flag you are trying to learn is already learnt.

    If the arm strap pager emits 4 consecutive beeps, it means that you attempt to register a sixth flag (max. 5 flags can be registered).

    If the red LED on the flag flashes twice and the flag does not vibrate after a press on the SIGNAL button, an error occurred during registration, please restart.


    How to reset the kit? (delete the flags from the armband case)
    Clear the memory of the arm strap pager

    (all flags will be deleted from the pager's memory):

    1 - Keep the ON/OFF and VOLUME buttons pressed for 10 seconds.

    2 - After 3 seconds, the green BATTERY LED turns on to indicate that the arm strap pager is in Registration mode. Keep the buttons pressed until the two red LEDs turn on simultaneously for 1 second and the pager vibrates to show that it has been successfully reset.

    Clear the memory of a flag

    (the flag will be deleted from the pager's memory):

    1 - Keep the SIGNAL button pressed for 20 seconds.

    2 - After 10 seconds, the green LED turns on to indicate that the flag is in Registration mode. Keep the button pressed until the red LED turns on for 1 second and the flag vibrates to indicate that it has been successfully reset.


chat Comments (1)
Grade